Input | 2 x 2/3/4 w RTD2 x TC (2/3/4 w ext. CJC)2 xTC (int. CJC)TC (int. CJC) + 2/3/4 w RTDTC (2/3 w ext. CJC) +2/3/4 w RTD2 x 2/3/4 w lin. R2 x 3/4 w Pot5 w Pot + 3 w Pot2 x mV unipolar2 x mV bipolar |
Output | 4...20 mA(Advanced functions) |
Version | Hazardous area |
Inputs | Dual input (7 terminals) |
SIL approval | No SIL |
Marine approval | No |
Operating temperature | -50°C to +85°C (standard) |
Storage temperature | -50°C to +85°C |
Calibration temperature | 23...25°C |
Relative humidity | < 99% RH (non-cond.) |
Protection degree (encl./terminal) | IP68 / IP00 |
Dimensions | Ø 44 x 20.2 mm |
Center hole diameter | Ø 6.35 mm / 1/4 in |
Weight approx | 50 g |
Wire size | 1 x 1.5 mm2stranded wire |
Screw terminal torque | 0.4 Nm |
Vibration | IEC 60068-2-6 |
2...25 Hz | ±1.6 mm |
25...100 Hz | ±4 g |
Supply voltage | 7.5*...30** VDC |
Internal power dissipation | ≤ 850 mW |
Additional min. supply voltage when using test terminals | 0.8 V |
Min. load resistance at >37 V supply | (Vsupply - 37) / 23 mA |
Isolation voltage, test / working | 2.5 kVAC / 42 VAC |
Response time | 70 ms |
Programmable damping | 0...60 s |
Polarity protection | All inputs and outputs |
Warm-up time | < 5 min. |
Start-up time | < 2.75 s |
Programming | Loop Link & HART |
Write protection | Jumper or software |
Signal / noise ratio | > 60 dB |
Long-term stability, better than | ±0.05% of span / year (±0.18% of span / 5 years) |
Signal dynamics, input | 24 bit |
Signal dynamics, output | 18 bit |
Effect of supply voltage change | < 0.005% of span / VDC |
EMC immunity influence | < ±0.1% of span |
Extended EMC immunity: NAMUR NE21, A criterion, burst | < ±1% |
RTD type | Pt10...10000, Ni10...10000, Cu5...1000 |
Cable resistance per wire | 50 Ω (max.) |
Effect of sensor cable resistance (3-/4-wire) | < 0.002 Ω / Ω |
Sensor current | < 0.15 mA |
Sensor error detection | None, Shorted, Broken, Shorted or Broken |
Thermocouple type | B, E, J, K, L, N, R, S, T, U, W3, W5, LR |
Cold junction compensation (CJC) | Constant, internal or external via a Pt100 or Ni100 sensor |
Sensor error detection | None, Shorted, Broken, Shorted or Broken |
Measurement range / min. range (span) | 0 Ω...100 kΩ / 25 Ω |
Cable resistance per wire (max.) | 50 Ω |
Sensor current | < 0.15 mA |
Sensor error detection | None, Broken |
Potentiometer min....max | 10 Ω...100 kΩ |
Measurement range / min. range (span) | 0...100% / 10% |
Cable resistance per wire (max.) | 50 Ω |
Sensor current | < 0.15 mA |
Sensor error detection | None, Shorted, Broken, Shorted or Broken |
Measurement range | -800...+800 mV (bipolar) |
Measurement range | -100 to 1700 mV |
Min. measurement range (span) | 2.5 mV |
Input resistance | 10 MΩ |
Sensor error detection | None, Broken |
Normal range, programmable | 3.8...20.5 / 20.5...3.8 mA |
Extended range (output limits), programmable | 3.5...23 / 23...3.5 mA |
Updating time | 10 ms |
Load (at current output) | ≤ (Vsupply -7.5)/0.023 [Ω] |
Load stability | < 0.01% of span / 100 Ω |
Sensor error indication | Programmable 3.5…23 mA |
NAMUR NE 43 Upscale/Downscale | > 21 mA / < 3.6 mA |
HART protocol revisions | HART 7 and HART 5 |
EMC | 2014/30/EU |
RoHS | 2011/65/EU |
EAC | TR-CU 020/2011 |
ATEX 2014/34/EU | DEKRA 16ATEX0047X |
IECEx | IECEx DEK. 16.0029X |
CSA | 70066266 |
FM | FM16US0287X / FM16CA0146X |
INMETRO | DEKRA 16.0008X |
NEPSI | GYJ18.1054X |
EAC Ex TR-CU 012/2011 | Pending |
EU RO Mutual Recognition Type Approval | Pending |