How to Use Vernier and Digital Calipers

Resource Description

How to Use Vernier and Digital Calipers

The Vernier Caliper is a precision tool that can be used for measuring internal as well as external ranges/intervals with exceptionally high accuracy. The measured results are interpreted from the tool’s scale by the operator. Dealing with a Vernier and interpreting its readings is rather difficult compared to using a Digital Caliper, its advanced version, which comes with an LCD digital display where all the readings are shown. As for the manual type of the tool - both imperial as well as metric scales are included.

Vernier Calipers are operated manually and still available to be purchased and remain popular because of being cheaper in comparison to the digital variant. On top of that, the digital variant needs a small battery while its manual counterpart does not require any power source. Nevertheless, a digital caliper provides a wider range of measurements.

In this article, the types, the fundamentals of measuring, and the readings of both Vernier as well as Digital calipers are described.

Using The Vernier:

To use this kind of device we need to follow the steps below:

  1. To measure outer dimensions of some item, the item is put within the jaws, which are then moved together until they secure the object.
  2. The first significant figures are read immediately to the left of the “zero” of the vernier scale.
  3. The digits remaining are taken from the vernier scale and placed after the decimal point of the basic reading. This remaining reading corresponds to the mark that is lined up with any main scale mark (or division). Only one division of the vernier scale fits together with one on the main scale.

Using The Vernier


Using a Digital Caliper:

Electronic Digital Calipers have become very affordable in recent years. They have several added features and capabilities compared to Vernier Calipers.

An electronic caliper has some buttons on the readout. One of which - to turn the tool on; another - to set it to zero; the third one - to switch between inches and millimeters and, in some models, to fractions. The precise situation of each button and how they are labeled differs depending on the manufacturer and the model. Some additional buttons might be added to your advantage as for example in Fowler™ Euro-Cal IV models, namely - Absolute to Incremental Measurements switch.

Using a Digital Caliper

The Very First Step

Before you take a reading - and this means before you take EVERY reading - close the caliper and make sure the reading is 0.000. If not, do this:

  1. Open the jaws about three quarters of an inch. Then use the thumb of your free hand to wipe off the mating surfaces of the jaws.
  2. Close the caliper again. In case if the reading is not 0.000 on an electronic caliper, press the zero button so that it does read 0.000. If you work with and need to zero a dial caliper, all you’ve got to do is rotate the bezel so that the needle is aligned with 0.

Four Basic Readings (common for vernier & digital)

Your caliper can take four kinds of readings: outside, inside, depth, and step. Any caliper, whether it is a vernier caliper or electronic digital caliper, can take these measurements. The only difference is that a digital caliper will save your time, showing you instant measuring numbers on the display. Let’s take a look at how you take each of those readings.

1. Outside Measurement

Outside measurements are the most basic you can do with a caliper. Slide the jaws open, place the caliper over the object to be measured, and slide the jaws until they contact the workpiece. Read the measurement.

It’s easy, but if you don’t do it correctly, the measurement will not be accurate. If the calipers are not straight (that is, perpendicular to the workpiece), the measurement will not be accurate. Likewise, if there's dirt on the jaws or the workpiece, the measurement will not be accurate.

2. Inside Measurement

The smaller jaws on the top of the caliper are used for inside measurements. Slide the caliper closed, place the inside-measuring jaws into the space to be measured, and slide the jaws apart as far as they will go. Read the measurement.

It’s a little harder to keep things lined up correctly when you are taking an inside measurement. Be sure that the calipers are not cocked, or you will not get an accurate measurement.

3. Depth measurement

As you open the caliper, the depth blade extends out of the far end. Use this blade to take depth measurements. Press the machined end of the caliper against the top of the hole you want to measure. Open the caliper until the depth blade contacts the bottom of the hole. Read the measurement.

It can be tricky keeping the caliper straight over the hole, especially if only one side of the caliper is resting on the workpiece.

4. Step Measurement

Step measurement is the hidden use of a caliper. Many instructions skip this important use. But once you know about it, you will find many uses for step measurement.

Open the caliper slightly. Place the sliding jaw on the upper step of the workpiece, then open the caliper until the fixed jaw contacts the lower step. Read the measurement.

Compound Measurements (digital calipers only)

Because you can zero an electronic digital caliper at any point, you can use it to do some of the arithmetic required for compound measurements.

Center Distance

Use this procedure to measure the center distance between two holes of equal diameter.

  1. Use the inside jaws to measure the diameter of one of the holes. Before you remove the caliper from the hole, press the button to zero the caliper while it is set to the diameter of the hole.
  2. Still using the inside jaws, measure the distance between the far surfaces of the two holes. The caliper reading is the distance between the centers of the two holes.

Be sure to use the same (inside) jaws for both measurements. And remember that this works only if the holes are the same size.

Comparing a hole to a shaft

Need to make a shaft or pin to fit an existing hole? Or are you boring a cylinder to fit a piston? You can use your electronic caliper to read the size difference directly.

  1. Use the inside jaws to measure the diameter of the hole. Before you remove the caliper from the hole, press the button to zero the caliper while it is set to the diameter of the hole.
  2. Use the outside jaws to measure the shaft. A positive reading (no minus sign displayed) shows that the shaft is larger than the hole. A negative reading (the minus sign appears to the left of the digits) shows that the shaft is smaller than the hole and will fit.

The caliper shows you how much material you need to remove, from either the shaft or the hole, to make them fit.

Calipers

Remaining Thickness

When you need to put a hole in a workpiece that does not go through, you might want to know how much material remains between the bottom of the hole and the other side of the workpiece. Your electronic caliper can display this distance for you.

Use the outside jaws to measure the total thickness of the workpiece. Before you remove the caliper from the workpiece, press the button to zero the caliper while it is set to the thickness of the workpiece.

Now use the depth blade to measure the depth of the hole. The caliper reading (shown as a negative number) is the remaining thickness between the bottom of the hole and the other side of the workpiece.

Related Products