Buy Elenco XK-700, Digital/Analog Trainer

info@MegaDepot.com

(800) 884-5767
+1 (332) 900-3727 (Intl.)

Congratulations on your purchase of the Elenco® Model XK-700 Digital / Analog Trainer. This trainer is designed to simplify designing of digital and analog circuits. It contains most of the necessary test equipment needed to build and test these circuits.

Your XK-700 has four basic trainers in a single package. They are, 5 independent power supplies, an analog trainer, a digital and a bredblock assembly trainer. We shall proceed in describing each trainer in the following sections.

Features

	Power Supply Model XK-700 has five built-in power supplies which will satisfy most design needs. This includes two variable power supplies giving up to +20 volts and -20 volts at .5 amp. Below 15V the current available is over 1 amp. Three fixed power supplies give you +12VDC, -12VDC or +5VDC at 1 amp each. These fixed voltages are the most commonly used voltages for design work. All supplies are regulated to within 150mV. This means that you can increase the current draw from no load to .5 amp and the voltage will change less than 150 millivolts. All supplies are also short circuit protected by using integrated circuit regulator devices.
	Analog Trainer Section Function Generator The analog trainer contain a complete function generator capable of producing sine, square and triangle waveform. The frequency of this generator is continuously variable from one hertz to over 100,000 hertz in five steps. A fine tuning control makes selection of any frequency easy. The output voltage amplitude is variable between 0 to 15Vpp. The output impedance is approximately 330 ohms.
	Digital Trainer Section The digital trainer has the necessary functions to do your digital designs. They consist of a clock generator, two no bounce logic switches, 8 LED indicator lamps and 8 data switches. These functions will make it easy to do your digital experiments.

See more product information See less

We aim to show you accurate product information. Here you will find what the manufacturers have provided us with. See our disclaimer.

Technical Details

Supplies

Optional Accessories

Reviews

Power Supplies

0V to 20VDC @ 0.5A (0V to 15V @ 1A)
0V to -20VDC @ 0.5A (0V to -15V @ 1A)
+12V + 5% @ 1A
-12V + 5% @ 1A
+5V + 5% @ 1A
30VAC center-tapped at 15VAC @ 1A.
Load regulation all DC supplies less than 0.2V no load to 0.5A
Line regulation all DC supplies less than 0.2V 105 to 135V
Hum and ripple all DC supplies less than .01V rms
Short protection all DC supplies-Internal IC thermal cutoff
Fuse - 1.25A 250V

Function Generator Analog Section

Waveforms sine, square, triangle, complimentary square
Frequency - 1Hz to 100kHz in 5 steps continuously variable
Fine frequency adjust - 10:1 approximate
Amplitude variable 0-15Vpp
Output impedance 330Ω: short protected
DC offset change + 10V from zero crossing

Digital Section

Data switches, eight DPDT, Hi 5V, low 0V
Logic switches, two no bounce with complimentary output “On” voltage level 2.8V min., “Off” voltage level 1V max. Input impedance 100kΩ.
Eight LED readouts, 100kΩ input impedance
Clock frequency, 1Hz to 100kHz in 5 steps continuously variable
Clock amplitude, 5Vpp squarewave
Clock rise time, better than 100nsec.

Bredboards Section

Two bredboards containing 830 tie points each (total 1,660 pins)
6 independent power bus lines for common connections

Notes

***

warning WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov

Product Details

Power Supplies

0V to 20VDC @ 0.5A (0V to 15V @ 1A)
0V to -20VDC @ 0.5A (0V to -15V @ 1A)
+12V + 5% @ 1A
-12V + 5% @ 1A
+5V + 5% @ 1A
30VAC center-tapped at 15VAC @ 1A.
Load regulation all DC supplies less than 0.2V no load to 0.5A
Line regulation all DC supplies less than 0.2V 105 to 135V
Hum and ripple all DC supplies less than .01V rms
Short protection all DC supplies-Internal IC thermal cutoff
Fuse - 1.25A 250V

Function Generator Analog Section

Waveforms sine, square, triangle, complimentary square
Frequency - 1Hz to 100kHz in 5 steps continuously variable
Fine frequency adjust - 10:1 approximate
Amplitude variable 0-15Vpp
Output impedance 330Ω: short protected
DC offset change + 10V from zero crossing

Digital Section

Data switches, eight DPDT, Hi 5V, low 0V
Logic switches, two no bounce with complimentary output “On” voltage level 2.8V min., “Off” voltage level 1V max. Input impedance 100kΩ.
Eight LED readouts, 100kΩ input impedance
Clock frequency, 1Hz to 100kHz in 5 steps continuously variable
Clock amplitude, 5Vpp squarewave
Clock rise time, better than 100nsec.

Bredboards Section

Two bredboards containing 830 tie points each (total 1,660 pins)
6 independent power bus lines for common connections

Supplies

Optional Accessories

Note

Note: Please read description carefully. Do not base your order on the picture presented.

Reviews

Elenco XK-700 Digital/Analog Trainer

Identifiers

Technical Details

Supplies

Optional Accessories

Reviews